The Conclusions and Recommendations may be combined or, in long reports, presented in separate sections.

Conclusions and recommendations

If there aren’t any recommendations to be manufactured as a consequence of the project, just call this section Conclusions.

The Conclusions section sums eliteessaywriters.com sign up up the main element points of the discussion, the essential top features of your design, or perhaps the significant outcomes of the investigation. As the function is always to round the story off of any project, it should:

  • be written to relate directly to the aims associated with the project as stated in the Introduction
  • indicate the extent to that the aims have already been achieved
  • summarise the key findings, outcomes or information in your report
  • acknowledge limitations while making suggestions for future work (where applicable)
  • Highlight the usefulness or significance of one’s work.

The conclusions should relate genuinely to the aims for the work:

The purpose of this project is to design a cell phone tower for a suburban location..

The cellular phone tower presented here can be erected safely in a suburban street.

It entails an overall total section of no more than 2m 2 l, and contains the safety that is following.

This investigation will review the volume of passengers making use of the Monash University Clayton-Caulfield inter-campus bus to be able to recommend adjustments towards the service if required.

Analysis regarding the survey data obtained in this project shows that use of the Clayton-Caulfield inter-campus bus has increased by 24% in past times five years. It is strongly suggested that frequency be increased during peak usage.

The Conclusions section below is from a level 2 Civil Engineering Alternative Designs report presenting two designs for a an overpass bridge. Go through the coloured buttons to look at comments.

Conclusions

Each one of the two bridge designs Lecturer’s comment:
An elegant beginning for a Conclusions follows on neatly from the preceding discussion. In this case, moreover it indicates that the aims associated with project have been met. presented in this report fulfil the criteria specified into the project brief. Both designs Lecturer’s comment:
The main findings or outcomes – in this case the important thing features of the designs – are then recapped. incorporate round piers on piled foundations, that are used because the soil conditions are unknown and perhaps unstable. Design 1, a simple i-girder that is composite, has the benefit of being manufactured from steel and therefore has longer spans and fewer piers.

Design 2, a super-T beam br >Design 2 Lecturer’s comment:
The importance of the outcome – in cases like this the final recommendation – is actually stated. is therefore recommended. It provides Lecturer’s comment:
To finish off, the achievement for the project is reinforced. An overpass that is affordable superior durability, and fully meets what’s needed associated with the design brief.

Always address limitations and suggest how they might be overcome in the future work. The excerpt below is through the Conclusions of a written report on a project investigating the end result of pulsation on heat transfer in horizontal pipe flow.

Experimental results Lecturer’s comment:
Key conclusions drawn through the project. indicated that pulsed flow without flow reversal had no effect that is significant with steady flow. Preliminary experiments with reversed flow, however, clearly indicated increased heat transfer. That is likely due Lecturer’s comment:
Provide a possible explanation for notable results, especially unexpected ones. to your large disturbances when you look at the boundary that is hydrodynamic once the flow changes direction. Further research Lecturer’s comment:
Recommend further research to deal with any extra work you think would be useful. is recommended to determine the utmost achievable enhancement.

It must be noted that Lecturer’s comment:
Acknowledge limitations or errors and suggest explanations and/or solutions. the experimental results usually do not concur with the equations that are theoretical. This can be as a result of the deposits which developed inside the pipe, or to inconsistent thermocouple temperature. Therefore, regular inspection regarding the test rig is recommended.

For a very long report, it really is acceptable to provide the conclusions and recommendations in point form:

The prototype robot courier presented here has been shown to be capable of delivering documents autonomously in an working office environment. It has demonstrated the following the different parts of mobile robotics:

  1. Localisation: The Kalman filter-based localisation algorithm achieved sub-centimeter accuracy under normal operating conditions.
  2. Environment modelling: The occupancy map was updated dynamically to add obstacles not within the map that is original.
  3. Path planning: A distance path that is transform-based using obstacle transforms produced a globally optimal local entrapment-free road to the target.